E-Maxx

alternative Traxxas #3978

alternative Traxxas #3959

alternative Traxxas #3960

alternative Traxxas #5379X

- Capacity: 7600mAh- Voltage: 7.4V- Max Continuous Discharge: 25C (190A)- Max Burst Discharge: 50C (380A)- Weight: 446g- Dimensions: 150.74*46.74*28.66mm - Balance Plug: JST-XH- Discharge Plug: XT90- Charge Rate: 1-3C Recommended, 5C Max

Bohrung: 1/8''=3,17mmMadenschraube: inklusiveBeispielabbildungAlternative zu Traxxas #3946

Bohrung: 1/8''=3,17mmMadenschraube: inklusiveBeispielabbildungAlternative zu Traxxas #3947

Bohrung: 1/8''=3,17mmMadenschraube: inklusiveAlternative zu Traxxas #3946Alternative zu Traxxas #3949

Alternative zu Hot Racing #TD100X06Alternative zu Hot Racing #TD90X06

This is the Hot Racing Black 65 T Spur Gear for the Traxxas New E-max, Summit and E-revoFEATURES:CNC Machined 6061-T6 aluminum hub Cap and Harden Black steel teeth attached to hub with three screwsYOU WILL RECEIVE:One Hot Racing Black 65T Spur GearREQUIREMENTS:Hardened 32P Steel pinon GearSPECIFICATIONS:65 teeth

- For six cell power Aluminum Outer Diff Case is a must; Revo and T-Maxx use RVO11L06, Summit use SUM11LH- Not intended for on road operation if the differential is replaced with a spool or lockeralternative Traxxas #5379X

Replace Traxxas Big Bore EX Long Shock TRA2661, 3762, 3762A, 2662length: 105mm (4-1/8") (not compressed)Mounting point 100mm (4")diameter: 19mm (3/4")Steel Shock Shaft 3.5mmSping 1.54mm wireDual rate 13 TurnAccept optional Shock boot if need.Can be use withSLF63FS261SLF63MR268SLF63RS286

One Steel slipper pressure plateOne Aluminum slipper hubOne Metallic Friction Materials Super Duty Slipper disk.alternative Traxxas #5351

This is a Power Double Up Slipper Pressure Plate and Slipper Hub for the Revo, T Maxx Summit,Long Chassis e-max 4x4 Slash Etc. .These are part of the slipper assembly.FEATURES:CNC Aluminum construction with Hard Anodizing.Allow you to double up the slipper surface to increass power tranfer.YOU WILL RECEIVE:One slipper pressure plateOne slipper hubREQUIREMENTS:Installation onto vehicle.COMMENTS:This replace TRA5351For double up the slipper surface you will need 2 set of TRA5352X TRX15HS, or TRX15GSHard Anodizing or Hardcoat is an electrochemically produced grey layer of hard aluminum oxide on the surface of aluminum components.

This is a Long Graphite Slipper Clutch for the Traxxas Revo and T-Maxx.FEATURES:Up grade your stock slipper clutchesHI Temp. Light weight Geaphite25% more surface areaYOU WILL RECEIVE:(3) Long Pads

FEATURES:25% more surface areaUp grade your stock slipper clutchesHI Temp. Hard Anodiz 7075 T6 AluminumCNC constructionYOU WILL RECEIVE:(3) Long PadsREQUIREMENTS:InstallationCOMMENTS:Hard Anodizing or Hardcoat is an electrochemically produced grey layer of hard aluminum oxide on the surface of aluminum components.

8mm ((M5 Lock Nut) Socket hex For the Revo T-Maxx Wheel7mm (M4 Lock Nut) Socket hex For 1/10 Wheel and 2wd Slipper4mm turnbuckle wrench for most 2WD Traxxas stock turnbuckle5mm turnbuckle wrench for most 4WD Traxxas stock turnbuckle

If your chassis did not come with the e-clip style suspension pins, you'll need Traxxas part #TRX4939X to complete the upper/lower arm installation.Some E-Maxx models came with a 6x13mm front outer bearing; if your stock bearings are 6x12mm then you'll need to buy 6x13mm bearings to be able to complete the installation.

Material: plastic

Material: plastic

Material: plastic

Material: plastic

Diameter: 165,9mmWidth: 107,8mmOffset: 0Hex: 17mmContent: 2 Wheels